Install xp reboot

For example, try the following:. On your computer, disk 0 may not be the correct disk, you can use "list disk" to find the correct disk. With your drive all ready, you can now launch the Windows XP setup with a few custom parameters. Remember that all USB devices will need to be plugged in right from the start while using the rescue drive. Replace C: with the drive you want to install Windows to. Proceed with the installation.

The setup program will then silently close, which might make you think that something went wrong. Don't worry though. Note: The above guide works with Windows XP only. Buy Now. Contact US. Insert the USB drive you intend to boot from. Instructions for doing so vary wildly from system to system, but generally entail the following: Reboot the system.

Go to the section that contains your boot devices. Exit from the BIOS configuration, saving all changes. Step 4: Prepping the Hard Disk You need to make sure that your hard drive is partitioned and formatted properly. To repartition and format This procedure will destroy any data on the hard drive : Click the icon on task bar to launch a command line Window. Enter DiskPart to run the built-in disk management utility. Click Next.

It's in the bottom-right corner of the window. You can also click Customize Enter your name, then click Next. Your name goes in the "Name" text field. You can also add a business name in the "Organization" section. Enter your product key, then click Next. Type the character key that you retrieved earlier into the "Product Key" boxes. Add a password, then click Next. Type your preferred password into the "Administrator password" and "Confirm password" text fields at the bottom of the window.

You can also change your computer's name in the text field at the top of the window. Set a date and time zone, then click Next. Click the "Date" drop-down box, select the current date, and then repeat with the "Time" and "Time Zone" boxes. Check the "Typical Settings" box, then click Next.

This will cause Windows XP to install using default settings. Check the "No" box. It's at the top of the window. If your computer is part of a workgroup, you'll instead check the "Yes" box and enter your workgroup's address in the text box.

This will complete the installation setup process, at which point Windows XP will resume installing. You may have to wait for 30 minutes or so before the installation finishes. It might be on a sticker on the bottom of your laptop if that's what you're using. Yes No. Not Helpful 13 Helpful Unless you keep a backup copy of your i folder, you can't. Ubuntu allows you to dual-boot your computer, which keeps both XP and Ubuntu.

Not Helpful 4 Helpful 9. I found an old XP computer. I want to factory reset it. How can I do that without knowing the admin password? Try to reintall the OS completely. Insert a official CD or dowload and make one. Then just install Windows normally. Not Helpful 0 Helpful 1. What can I do if my computer won't boot up, shows Windows, then shuts down and tries to start up again, then loops?

Repeatedly hit F8 on your keyboard during boot up, than select system repair. If you can't, contact your system manufacturer for a repair CD. Or, if you have to product code, download from the Microsoft website.

Not Helpful 9 Helpful 3. Boot into the Windows XP installation, get to the partitions, then format the drive. Just make sure you backed up all files. Not Helpful 0 Helpful 0. However, at the minimum RAM, Vista will be quite laggy. You might want to consider upgrading your RAM to its maximum amount, which should be quite inexpensive on an older machine; if the processor is at least 1 GHz, you could then run Windows 7. What to do in that case? It may be in a hidden file. Search for winnt in My Computer.

If you see an icon that looks like a computer next to something that says "winnt", that is the. Double click on that icon and walk through the steps.

You can find your system information by either checking the computer manufacturer's manual, or by running DirectX Diagnostic on an existing Windows operating system of the computer. It is printed on a sticker on your software package or located on the computer itself. It is a string of 5 groups of characters each 5 long , separated by dashes, resulting in 25 characters in all.

You need the product key to complete installing Windows. Before inserting the CD, you'll need to set your computer to boot from a CD instead of from the hard drive. This will allow you to load the Windows XP setup files before your computer boots to its installed operating system. Click the green "BIOS" link for more information. You may need to have the USB drive inserted for it to appear as an option.

Part 2. Load the installer. Your computer will reboot and you will be presented with the message: Press any key to boot from CD. Press any key on your keyboard to start the Setup program. Setup will load files necessary to begin the installation, which may take a few moments.

Once the loading is complete, you will be taken to the Welcome screen. Read the License Agreement. After reading, press F8 indicating you agree to the terms. Select the partition you want to install on. You will see a list of available partitions on your installed hard drives.

If you are installing Windows XP on a new hard drive, you should see only one entry labeled "Unpartitioned space. Installing Windows XP will erase all of the data on the partition that you choose. Select a partition that is empty or that contains data that you do not care to lose. Any data on the partition will be lost when it is deleted. Create a new partition. By default, the partition will be set to the maximum amount of available space.

Unless you plan on creating multiple partitions, you can usually leave this at its default. Windows XP requires at least 1. You can create multiple partitions on a single drive. This can allow you to separate your programs from your movies and music, or to install another operating system. Windows XP can only be installed on one discrete partition. Select your new partition. NTFS is the preferred method, supporting a larger amount of disk space per partition than FAT, and including security features at the file system level.

NTFS also includes system level compression. There are almost no situations anymore where choosing FAT would be preferable. It is highly recommended to avoid Quick Format, as this skips an important process that checks the hard drive for errors or bad sectors. This scan is what consumes the majority of the time taken when performing a full format. If there are errors on a disk at the physical level, it's best to catch them now rather than later.

Wait for the format to complete. The system will now format the partition. The length of time this process requires depends on the speed and size of the drive. In general, the larger the partition, the longer the process will take. Wait for the Setup files to copy. Windows will now start copying files from the installation disc and prompt you to reboot the computer when the process is completed. Allow the computer to boot normally. You will see the message asking you to press a key to boot from CD.

Ignore it and allow the computer to continue booting from the hard drive. You will see the Windows logo as the Setup program loads. Wait for the installation to proceed. After the Windows logo goes away, you will see a list of steps remaining on the left side of the screen, and tips for using windows on the right. The time remaining for the installation will be displayed below the list of steps remaining.

It is normal for the screen to flicker, turn on and off, or resize during this process. Choose your language and region settings. During the installation process a dialog window will appear, asking you to choose your Regional settings.